EKM Omnimeter Pulse v.4 – Pulse Counting, Relay Controlling, Universal Smart Electric Meter

More Views

EKM Omnimeter Pulse v.4 – Pulse Counting, Relay Controlling, Universal Smart Electric Meter
$220.00

Availability: In stock

This universal kWh meter can be used on nearly any electrical system in common use and can also count pulses from up to 3 pulse-output devices, as well as control up to 2 external relays.
OR
Description

Details

Description: Universal, Pulse Counting, Relay Controlling, Smart Meter

Features: Pulse Counting and Relay Controls

Voltage: 120 volts, 120/240 volts, 120/208 volts, 230 volts, 277 volts, 480 volts

Amperage: Up to 5000 amps

Type: External CT, 50 or 60 Hz

System: Single-Phase, 3-Ph. 3-Wire, or 3-Ph. 4-wire

Data: Smart Meter v.4 RS-485 Communications

Model: EKM-Omnimeter Pulse v.4

EKM-OmniMeter Pulse v.4 -- Our Most Advanced Universal Smart Meter to date, now with the ability to count pulses from up to 3 pulse-output devices, and control 2 external relays. This is truly the one meter to meet all of your metering needs!

The Omnimeter Pulse v.4 can count the pulses from up to 3 different pulse output devices. These could be pulses from our Pulse Output Water and Gas Meters or from any other un-powered dry contact pulse output device. Pulse Input ratios can be set in software from 1 to 9999 pulses per increment (the default ratio is now 1:1). The real-time state of the 3 Inputs can also be polled in EKM Dash software, the Omnimeter Pulse v.4 will return a High or Low state for each pin in real-time (use this for sensing switch states, open or closed doors, etc).

The Omnimeter Pulse v.4 comes with 2 controllable relay outputs. These can be controlled via RS-485, either locally or over the internet from anywhere in the world using the EKM Dash. You can set the outputs to be high or low to drive an external relay. The Relay Control Outputs can continuously provide up to 50 mA at 12 volts DC each. Control the EKM-Switch120 directly, or control lights, motors, entire buildings, implement Demand Response, Load Shedding, etc. via relay control. The Relay Control Outputs can also be set to go ON or OFF from 1 to 9999 seconds. The real-time state of the outputs can also be polled via RS485. The outputs can also be used to power an external device (Wireless 485Bee Module, sensors, etc).

The Omnimeter Pulse is also a revenue-grade universal kWh meter. It can meter systems ranging from single-phase 120V 2-wire or single phase 120/240V 3-wire, 120V to 480 volts, or 3-phase 3-wire 120 to 400 volts or 3-phase 4-wire 120 to 480V, 50/60Hz , 50/60 Hz. It Supports CTs from 100A to 5000A. This meter will work with any system that is commonly used in the world. Accurate to 0.5% (Class 0.5)

This meter features RS-485 communications for remote reading. It is also supported by our revolutionary cloud-based communication system that we call EKM Push. EKM Push users can also take advantage of Encompass, which is our free online dashboard and meter management suite.

The EKM Push is also fully supported by our remote reading, EKM Dash software.

This meter uses our full range of compact Current Transformers (you cannot meter electricity without at least one of these). The CT ratio can be set internally in the meter in order for it to work with up to 5000 amp CTs (no multiplier needed).

  • Use 1 CT for 120 volt single phase North American, or 230 volt 2-wire foreign systems
  • Use 2 CTs for 120/240 volt single phase systems
  • Use 2 CTs for 3-phase 3-wire systems (no neutral)
  • Use 3 CTs for 3-phase 4-wire systems

The Omnimeter Pulse is also great option for solar Net Metering. In addition to Total and Reverse kWh, that all of our Omnimeter models provide, these meters also provide the direction of current in real time. This makes it possible to know, in real time, if you are generating more power than you are consuming, and whether you are sending or pulling power, to or from the grid. This meter is listed by the California Solar Initiative as eligible for Performance Based Incentives (PBI). In other words, you may be eligible to earn money back from your Utility, in California and some other States, by using one these meters to monitor the performance of your solar array. Check with your local Utility to see if you are eligible.

How to install an Omnimeter Pulse v.4:

For more information about our products and services, we encourage you to visit our online Knowledge Base, which provides spec sheets, videos, tutorials, FAQs, diagrams, and more.

Easy clip-on DIN Rail Mounting.

EKM Widget

Use the Omnimeter in conjunction with an EKM Push gateway to provide rich, real-time and historical data. The Widgets below provide one way to visualize your meter data in real-time, as well as your usage history. More info here: EKM Widget

Spec Sheet: Omnimeter Pulse Spec Sheet




To better understand the differences between Omnimeter models you can download our Omnimeter and Communication Device Comparison Chart.

Additional Information

Additional Information

Manufacturer No
Questions and Answers
Questions & Answers
Expand all
Sort by
Most Recent Questions
Q:
Hey,
I am looking for the price of meter type 4 and 4a, 1 and 3 phase. Please reply ASAP, if you have them. Thanks
1 answers
Q:
Looking for a meter with only demand KW read out from utility pulse meter.
What Model to use?
1 answers
Q:
Is this meter UL approved?
1 answers
Q:
I'm looking to connect the dry kyz outputs of a ION 8650 meter to the Omnimeter Pulse v.4 to count the pulses from the kyz outputs, convert the pulses to kWh, based on pulse wait, then finally have another device fetch the data via the serial port. Can this be done with the Omnimeter Pulse V.4?
1 answers
Q:
Hi there, the relay control on these meters - Can these be set up for automated switching by programming preset thresholds etc, or are they only manually controlled?

Alternatively, is there any automated (via presets) remote controlling options via the EKM dash?
1 answers
Q:
If I customize the display values, will this be reset if power is lost?
1 answers
Q:
I'm hoping to use this with the 3/4" stainless steel pulse output flow meter. Can this omnimeter v.4 unit be powered by 12v? Also, how is the omnimeter reset?
1 answers
Q:
Will this electrical meter accept a pulse output from another electrical meter such as the EKM-25IDS? I want to monitor my home energy usage as well as the branch circuit usage to my detached garage.
1 answers
Q:
Can separate readings for each CT and each additional pulse output device be generated from this meter to determine the electrical consumption of multiple tenants without additional meters?
1 answers
Q:
It's stated that the relay control output is 12V at 50 mA, is this AC or DC?
1 answers
* Nickname:

* Your Answer:


Sign Up for Newsletter

*Protection Code:

Please, enter the text shown in the image into the field below
CAPTCHA Image
Reload the Image

* Nickname:

* Your Question:


Notify me by email when answer received

Sign Up for Newsletter

*Protection Code:

Please, enter the text shown in the image into the field below
CAPTCHA Image
Reload the Image

Installer Directory
Reviews

Customer Reviews 1 item(s)

Excellent Product
This meter is awesome. We have a solar PV array on our house, and even though it cant work with the PUSH system yet, it still indicates the direction of current. Well done. Great product.
Price
Value
Quality
Review by Chris Saksida / (Posted on 10/6/2014)

You may also be interested in the following product(s)